DDR Version V1.06 20220224
LPDDR4, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-gbdb740d4da-220216 #cjh (Feb 24 2022 - 03:15:33)
Failed to set cpub01
Failed to set cpub23
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 1
spl: mmc init failed with error: -123
Trying to boot from MMC1
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(4e081b1b07...) + OK
## Checking uboot 0x00200000 ... sha256(4ded8b645f...) + OK
## Checking fdt 0x00320438 ... sha256(c07f4a4d71...) + OK
## Checking atf-2 0x000f0000 ... sha256(6a00298af8...) + OK
## Checking atf-3 0xff100000 ... sha256(19762d10e3...) + OK
## Checking atf-4 0xff009000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(603cfbd25d...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 86.337 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-331-g7380d9813:derrick.huang
NOTICE:  BL31: Built : 19:33:36, Mar 24 2022
INFO:    timer_hp_init no valid 32k timer source, use normal mode
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9
INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
INFO:    hdmirx_handler: dma not on, ret
I/TC: 
I/TC: OP-TEE version: 3.13.0-639-g8e053a881-dev #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon Mar 14 09:09:01 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-dirty # (Aug 06 2022 - 15:34:09 +0800)

Model: Rockchip RK3588 Evaluation Board
PreSerial: 2, raw, 0xfeb50000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: edb57000
Relocation fdt: eb9fa108 - eb9fecd0
CR: M/C/I
Using default environment

mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v2
boot mode: normal
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found! Error: -2
en-gpios- not found! Error: -2
vdd_cpu_big0_s0 675000 uV
vsel-gpios- not found! Error: -2
en-gpios- not found! Error: -2
vdd_cpu_big1_s0 675000 uV
I2c1 speed: 100000Hz
vsel-gpios- not found! Error: -2
en-gpios- not found! Error: -2
vdd_npu_s0 837500 uV
spi2: RK806: 2
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_log_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
vdd_ddr_s0 850000 uV
get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
Could not find baseparameter partition
Model: HSZN RK3588 R1V1 Board
Rockchip UBOOT DRM driver version: v1.0.1
vp0 have layer nr:2[0 2 ], primary plane: 2
vp1 have layer nr:2[1 3 ], primary plane: 3
vp2 have layer nr:2[6 8 ], primary plane: 8
vp3 have layer nr:2[7 9 ], primary plane: 9
hdmi@fde80000 disconnected
hdmi@fdea0000 disconnected
CLK: (uboot. arm: enter 1200000 KHz, init 1200000 KHz, kernel 0N/A)
  b0pll 1200000 KHz
  b1pll 1200000 KHz
  lpll 1200000 KHz
  v0pll 24000 KHz
  aupll 786215 KHz
  cpll 1500000 KHz
  gpll 1188000 KHz
  npll 850000 KHz
  ppll 100000 KHz
  aclk_center_root 702000 KHz
  pclk_center_root 100000 KHz
  hclk_center_root 396000 KHz
  aclk_center_low_root 500000 KHz
  aclk_top_root 750000 KHz
  pclk_top_root 100000 KHz
  aclk_low_top_root 396000 KHz
Net:   eth1: ethernet@fe1c0000, eth0: ethernet@fe1b0000
Hit key to stop autoboot('CTRL+C'):  0 
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe9a71ac0 with size 0x01d87600
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e9a71ac0 ...
   Using 'conf' configuration
## Verified-boot: 0
   Trying 'kernel' kernel subimage
     Description:  unavailable
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0xe9a98ec0
     Data Size:    30801928 Bytes = 29.4 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x00400000
     Entry Point:  0x00400000
     Hash algo:    sha256
     Hash value:   b7fbfecb93da51eee3ca8f0b36b850d335551a1c7202ad24d3dbdc32f1407122
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at e9a71ac0 ...
   Using 'conf' configuration
   Trying 'fdt' fdt subimage
     Description:  unavailable
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0xe9a722c0
     Data Size:    158681 Bytes = 155 KiB
     Architecture: AArch64
     Load Address: 0x0a100000
     Hash algo:    sha256
     Hash value:   46cf24351d9d1e8491634228d2a946f6cc93de0fac76b3537510f96658a66aac
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x0a100000 to 0x0a100000
   Booting using the fdt blob at 0x0a100000
   Loading Kernel Image from 0xe9a98ec0 to 0x00400000 ... OK
   kernel loaded at 0x00400000, end = 0x02160008
  'reserved-memory' cma: addr=10000000 size=10000000
   Using Device Tree in place at 000000000a100000, end 000000000a129bd8
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 525.232 ms

Starting kernel ...

[    0.636853] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    0.636875] Linux version 5.10.66 (root@1760bd274111) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #1 SMP Wed Aug 10 08:57:46 CST 2022
[    0.647375] Machine model: HSZN RK3588 R1V1 Board
[    0.647444] earlycon: uart8250 at MMIO32 0x00000000feb50000 (options '')
[    0.651500] printk: bootconsole [uart8250] enabled
[    0.657509] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
[    0.658654] Reserved memory: created CMA memory pool at 0x0000000010000000, size 256 MiB
[    0.659397] OF: reserved mem: initialized node cma, compatible id shared-dma-pool
[    0.804041] Zone ranges:
[    0.804288]   DMA      [mem 0x0000000000200000-0x00000000ffffffff]
[    0.804862]   DMA32    empty
[    0.805132]   Normal   [mem 0x0000000100000000-0x00000001ffffffff]
[    0.805703] Movable zone start for each node
[    0.806095] Early memory node ranges
[    0.806427]   node   0: [mem 0x0000000000200000-0x00000000083fffff]
[    0.807004]   node   0: [mem 0x0000000009400000-0x00000000efffffff]
[    0.807581]   node   0: [mem 0x0000000100000000-0x00000001ffffffff]
[    0.808160] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[    0.851883] psci: probing for conduit method from DT.
[    0.852357] psci: PSCIv1.1 detected in firmware.
[    0.852782] psci: Using standard PSCI v0.2 function IDs
[    0.853265] psci: Trusted OS migration not required
[    0.853717] psci: SMC Calling Convention v1.2
[    0.854506] percpu: Embedded 30 pages/cpu s85352 r8192 d29336 u122880
[    0.855295] Detected VIPT I-cache on CPU0
[    0.855709] CPU features: detected: GIC system register CPU interface
[    0.856301] CPU features: detected: Virtualization Host Extensions
[    0.856875] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.857520] alternatives: patching kernel code
[    0.858226] Built 1 zonelists, mobility grouping on.  Total pages: 1995336
[    0.858864] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal  androidboot.verifiedbootstate=orange rw rootwait earlycon=uart8250,mmio32,0xfeb50000 console=ttyFIQ0 irqchip.gicv3_pseudo_nmi=0 root=PARTUUID=614e0000-0000
[    0.862222] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.863410] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.864131] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.872025] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[    0.945737] Memory: 7591456K/8108032K available (14910K kernel code, 3200K rwdata, 5684K rodata, 6208K init, 521K bss, 254432K reserved, 262144K cma-reserved)
[    0.947179] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.947813] ftrace: allocating 56587 entries in 222 pages
[    1.048435] ftrace: allocated 222 pages with 6 groups
[    1.049198] rcu: Hierarchical RCU implementation.
[    1.049635] rcu:     RCU event tracing is enabled.
[    1.050053]  Rude variant of Tasks RCU enabled.
[    1.050472] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    1.056546] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    1.059208] GICv3: GIC: Using split EOI/Deactivate mode
[    1.059694] GICv3: 480 SPIs implemented
[    1.060048] GICv3: 0 Extended SPIs implemented
[    1.060481] GICv3: Distributor has no Range Selector support
[    1.061008] GICv3: 16 PPIs implemented
[    1.061397] GICv3: CPU0: found redistributor 0 region 0:0x00000000fe680000
[    1.062157] ITS [mem 0xfe640000-0xfe65ffff]
[    1.062598] ITS@0x00000000fe640000: allocated 8192 Devices @1001e0000 (indirect, esz 8, psz 64K, shr 0)
[    1.063485] ITS@0x00000000fe640000: allocated 32768 Interrupt Collections @1001f0000 (flat, esz 2, psz 64K, shr 0)
[    1.064439] ITS: using cache flushing for cmd queue
[    1.064922] ITS [mem 0xfe660000-0xfe67ffff]
[    1.065357] ITS@0x00000000fe660000: allocated 8192 Devices @100210000 (indirect, esz 8, psz 64K, shr 0)
[    1.066243] ITS@0x00000000fe660000: allocated 32768 Interrupt Collections @100220000 (flat, esz 2, psz 64K, shr 0)
[    1.067195] ITS: using cache flushing for cmd queue
[    1.067822] GICv3: using LPI property table @0x0000000100230000
[    1.068512] GIC: using cache flushing for LPI property table
[    1.069038] GICv3: CPU0: using allocated LPI pending table @0x0000000100240000
[    1.069872] random: get_random_bytes called from start_kernel+0x3dc/0x5d0 with crng_init=0
[    1.206194] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    1.207520] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    1.208517] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    1.210366] Console: colour dummy device 80x25
[    1.210806] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    1.211756] pid_max: default: 32768 minimum: 301
[    1.212327] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.213040] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.215483] rcu: Hierarchical SRCU implementation.
[    1.216761] Platform MSI: msi-controller@fe640000 domain created
[    1.217358] Platform MSI: msi-controller@fe660000 domain created
[    1.218224] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe640000 domain created
[    1.219010] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe660000 domain created
[    1.220264] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
I/TC: Secondary CPU 4 initializing
I/TC: Secondary CPU 4 switching to normal world boot
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
[    1.221971] Detected VIPT I-cache on CPU1
[    1.222011] GICv3: CPU1: found redistributor 100 region 0:0x00000000fe6a0000
[    1.222030] GICv3: CPU1: using allocated LPI pending table @0x0000000100250000
[    1.222079] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[    1.223421] Detected VIPT I-cache on CPU2
[    1.223454] GICv3: CPU2: found redistributor 200 region 0:0x00000000fe6c0000
[    1.223472] GICv3: CPU2: using allocated LPI pending table @0x0000000100260000
[    1.223518] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[    1.224879] Detected VIPT I-cache on CPU3
[    1.224908] GICv3: CPU3: found redistributor 300 region 0:0x00000000fe6e0000
[    1.224926] GICv3: CPU3: using allocated LPI pending table @0x0000000100270000
[    1.224969] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[    1.226281] CPU features: detected: Spectre-v4
[    1.226285] Detected PIPT I-cache on CPU4
[    1.226301] GICv3: CPU4: found redistributor 400 region 0:0x00000000fe700000
[    1.226312] GICv3: CPU4: using allocated LPI pending table @0x0000000100280000
[    1.226339] CPU4: Booted secondary processor 0x0000000400 [0x414fd0b0]
[    1.227604] Detected PIPT I-cache on CPU5
[    1.227622] GICv3: CPU5: found redistributor 500 region 0:0x00000000fe720000
[    1.227633] GICv3: CPU5: using allocated LPI pending table @0x0000000100290000
[    1.227662] CPU5: Booted secondary processor 0x0000000500 [0x414fd0b0]
[    1.228956] Detected PIPT I-cache on CPU6
[    1.228973] GICv3: CPU6: found redistributor 600 region 0:0x00000000fe740000
[    1.228984] GICv3: CPU6: using allocated LPI pending table @0x00000001002a0000
[    1.229012] CPU6: Booted secondary processor 0x0000000600 [0x414fd0b0]
[    1.230262] Detected PIPT I-cache on CPU7
[    1.230279] GICv3: CPU7: found redistributor 700 region 0:0x00000000fe760000
[    1.230290] GICv3: CPU7: using allocated LPI pending table @0x00000001002b0000
[    1.230318] CPU7: Booted secondary processor 0x0000000700 [0x414fd0b0]
[    1.230399] smp: Brought up 1 node, 8 CPUs
[    1.247143] SMP: Total of 8 processors activated.
[    1.247579] CPU features: detected: Privileged Access Never
[    1.248093] CPU features: detected: User Access Override
[    1.248583] CPU features: detected: 32-bit EL0 Support
[    1.249067] CPU features: detected: Common not Private translations
[    1.249647] CPU features: detected: RAS Extension Support
[    1.250143] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    1.250935] CPU features: detected: CRC32 instructions
[    1.251407] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    1.252050] CPU features: detected: RCpc load-acquire (LDAPR)
[    1.252688] CPU: All CPU(s) started at EL2
[    1.254489] devtmpfs: initialized
[    1.265194] Registered cp15_barrier emulation handler
[    1.265672] Registered setend emulation handler
[    1.266176] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    1.267095] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    1.270349] pinctrl core: initialized pinctrl subsystem
[    1.271262] NET: Registered protocol family 16
[    1.272653] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    1.273424] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    1.274737] thermal_sys: Registered thermal governor 'fair_share'
[    1.274740] thermal_sys: Registered thermal governor 'step_wise'
[    1.275307] thermal_sys: Registered thermal governor 'user_space'
[    1.275864] thermal_sys: Registered thermal governor 'power_allocator'
[    1.276571] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    1.277960] thermal thermal_zone2: power_allocator: sustainable_power will be estimated
[    1.278733] thermal thermal_zone3: power_allocator: sustainable_power will be estimated
[    1.279507] thermal thermal_zone4: power_allocator: sustainable_power will be estimated
[    1.280280] thermal thermal_zone5: power_allocator: sustainable_power will be estimated
[    1.281053] thermal thermal_zone6: power_allocator: sustainable_power will be estimated
[    1.281820] cpuidle: using governor menu
[    1.282192] Registered FIQ tty driver
[    1.282705] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    1.283462] ASID allocator initialised with 65536 entries
[    1.285795] printk: console [ramoops-1] enabled
[    1.286218] pstore: Registered ramoops as persistent store backend
[    1.286794] ramoops: using 0xf0000@0x110000, ecc: 0
[    1.331796] rockchip-gpio fd8a0000.gpio: probed /pinctrl/gpio@fd8a0000
[    1.332647] rockchip-gpio fec20000.gpio: probed /pinctrl/gpio@fec20000
[    1.333475] rockchip-gpio fec30000.gpio: probed /pinctrl/gpio@fec30000
[    1.334339] rockchip-gpio fec40000.gpio: probed /pinctrl/gpio@fec40000
[    1.335208] rockchip-gpio fec50000.gpio: probed /pinctrl/gpio@fec50000
[    1.335844] rockchip-pinctrl pinctrl: probed pinctrl
[    1.350049] fiq_debugger fiq_debugger.0: IRQ fiq not found
[    1.350567] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[    1.351113] fiq_debugger_probe: could not install nmi irq handler
[ [    1.351725] printk: console [ttyFIQ0] enabled
   1.351725] printk: console [ttyFIQ0] enabled
[    1.352510] printk: bootconsole [uart8250] disabled
[    1.352510] printk: bootconsole [uart8250] disabled
[    1.353062] Registered fiq debugger ttyFIQ0
[    1.353419] vcc5v0_sys: supplied by vcc12v_dcin
[    1.353556] vcc5v0_usbdcin: supplied by vcc12v_dcin
[    1.353686] vcc5v0_usb: supplied by vcc5v0_usbdcin
[    1.353919] vbus5v0_typec: supplied by vcc5v0_usb
[    1.354047] vcc_1v1_nldo_s3: supplied by vcc5v0_sys
[    1.354227] vcc5v0_host: supplied by vcc5v0_usb
[    1.354733] iommu: Default domain type: Translated 
[    1.354815] rk_iommu fdab9000.iommu: version = 2
[    1.355199] rk_iommu fdb50800.iommu: version = 2
[    1.355436] rk_iommu fdb60f00.iommu: version = 2
[    1.355627] rk_iommu fdb70f00.iommu: version = 2
[    1.355797] rk_iommu fdb90480.iommu: version = 2
[    1.355978] rk_iommu fdba0800.iommu: version = 2
[    1.356162] rk_iommu fdba4800.iommu: version = 2
[    1.356343] rk_iommu fdba8800.iommu: version = 2
[    1.356527] rk_iommu fdbac800.iommu: version = 2
[    1.356709] rk_iommu fdbb0800.iommu: version = 2
[    1.356888] rk_iommu fdbdf000.iommu: version = 2
[    1.357126] rk_iommu fdbef000.iommu: version = 2
[    1.357382] rk_iommu fdc38700.iommu: version = 2
[    1.357635] rk_iommu fdc48700.iommu: version = 2
[    1.357802] rk_iommu fdd97e00.iommu: version = 2
[    1.358134] SCSI subsystem initialized
[    1.358222] usbcore: registered new interface driver usbfs
[    1.358240] usbcore: registered new interface driver hub
[    1.358257] usbcore: registered new device driver usb
[    1.358296] mc: Linux media interface: v0.10
[    1.358308] videodev: Linux video capture interface: v2.00
[    1.358336] pps_core: LinuxPPS API ver. 1 registered
[    1.358341] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    1.358350] PTP clock support registered
[    1.358616] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[    1.358655] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[    1.359755] Advanced Linux Sound Architecture Driver Initialized.
[    1.359961] Bluetooth: Core ver 2.22
[    1.359978] NET: Registered protocol family 31
[    1.359982] Bluetooth: HCI device and connection manager initialized
[    1.359988] Bluetooth: HCI socket layer initialized
[    1.359993] Bluetooth: L2CAP socket layer initialized
[    1.360002] Bluetooth: SCO socket layer initialized
[    1.361309] rockchip-cpuinfo cpuinfo: SoC            : 35880000
[    1.361316] rockchip-cpuinfo cpuinfo: Serial         : 540b48857faab6f3
[    1.361673] clocksource: Switched to clocksource arch_sys_counter
[    1.646582] NET: Registered protocol family 2
[    1.646752] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    1.648700] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear)
[    1.648801] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    1.649142] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
[    1.649918] TCP: Hash tables configured (established 65536 bind 65536)
[    1.649977] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear)
[    1.650130] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear)
[    1.650347] NET: Registered protocol family 1
[    1.650640] RPC: Registered named UNIX socket transport module.
[    1.650649] RPC: Registered udp transport module.
[    1.650652] RPC: Registered tcp transport module.
[    1.650656] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.651118] PCI: CLS 0 bytes, default 64
[    1.652185] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[    1.654445] Initialise system trusted keyrings
[    1.654525] workingset: timestamp_bits=62 max_order=21 bucket_order=0
[    1.656776] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.657047] NFS: Registering the id_resolver key type
[    1.657058] Key type id_resolver registered
[    1.657061] Key type id_legacy registered
[    1.657081] ntfs: driver 2.1.32 [Flags: R/O].
[    1.657147] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    1.657217] fuse: init (API version 7.32)
[    1.657350] SGI XFS with security attributes, no debug enabled
[    1.678705] NET: Registered protocol family 38
[    1.678716] Key type asymmetric registered
[    1.678720] Asymmetric key parser 'x509' registered
[    1.678738] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[    1.678742] io scheduler mq-deadline registered
[    1.678746] io scheduler kyber registered
[    1.687567] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx phy init success
[    1.688368] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy init success
[    1.690829] rk-pcie fe170000.pcie: invalid prsnt-gpios property in node
[    1.690886] rk-pcie fe170000.pcie: no vpcie3v3 regulator found
[    1.690976] pwm-backlight backlight: supply power not found, using dummy regulator
[    1.691188] rk-pcie fe170000.pcie: missing legacy IRQ resource
[    1.691191] mpp_service mpp-srv: 15e4fdd7e064 author: Herman Chen 2022-04-13 video: rockchip: mpp: rkvenc2: Fix dchs conflict
[    1.691197] mpp_service mpp-srv: probe start
[    1.691212] rk-pcie fe170000.pcie: IRQ msi not found
[    1.691222] rk-pcie fe170000.pcie: use outband MSI support
[    1.691232] rk-pcie fe170000.pcie: Missing *config* reg space
[    1.691251] rk-pcie fe170000.pcie: host bridge /pcie@fe170000 ranges:
[    1.691278] rk-pcie fe170000.pcie:      err 0x00f2000000..0x00f20fffff -> 0x00f2000000
[    1.691299] rk-pcie fe170000.pcie:       IO 0x00f2100000..0x00f21fffff -> 0x00f2100000
[    1.691321] rk-pcie fe170000.pcie:      MEM 0x00f2200000..0x00f2ffffff -> 0x00f2200000
[    1.691338] rk-pcie fe170000.pcie:      MEM 0x0980000000..0x09bfffffff -> 0x0980000000
[    1.691374] rk-pcie fe170000.pcie: Missing *config* reg space
[    1.691415] rk-pcie fe170000.pcie: invalid resource
[    1.692600] mpp_vdpu2 fdb50400.vdpu: Adding to iommu group 1
[    1.692820] mpp_vdpu2 fdb50400.vdpu: probe device
[    1.692940] mpp_vdpu2 fdb50400.vdpu: reset group is empty!
[    1.692945] vdpu_init:498: No aclk reset resource define
[    1.692950] mpp_vdpu2 fdb50400.vdpu: reset group is empty!
[    1.692955] vdpu_init:501: No hclk reset resource define
[    1.693060] mpp_vdpu2 fdb50400.vdpu: probing finish
[    1.693253] mpp_vepu2 jpege-ccu: probing start
[    1.693259] mpp_vepu2 jpege-ccu: probing finish
[    1.693375] mpp_vepu2 fdba0000.jpege-core: Adding to iommu group 5
[    1.693466] mpp_vepu2 fdba0000.jpege-core: probing start
[    1.693592] mpp_vepu2 fdba0000.jpege-core: attach ccu success
[    1.693685] mpp_vepu2 fdba0000.jpege-core: probing finish
[    1.693766] mpp_vepu2 fdba4000.jpege-core: Adding to iommu group 6
[    1.693858] mpp_vepu2 fdba4000.jpege-core: probing start
[    1.693990] mpp_vepu2 fdba4000.jpege-core: attach ccu success
[    1.694079] mpp_vepu2 fdba4000.jpege-core: probing finish
[    1.694161] mpp_vepu2 fdba8000.jpege-core: Adding to iommu group 7
[    1.694254] mpp_vepu2 fdba8000.jpege-core: probing start
[    1.694382] mpp_vepu2 fdba8000.jpege-core: attach ccu success
[    1.694474] mpp_vepu2 fdba8000.jpege-core: probing finish
[    1.694545] mpp_vepu2 fdbac000.jpege-core: Adding to iommu group 8
[    1.694640] mpp_vepu2 fdbac000.jpege-core: probing start
[    1.694767] mpp_vepu2 fdbac000.jpege-core: attach ccu success
[    1.694855] mpp_vepu2 fdbac000.jpege-core: probing finish
[    1.695143] mpp-iep2 fdbb0000.iep: Adding to iommu group 9
[    1.695244] mpp-iep2 fdbb0000.iep: probe device
[    1.695393] mpp-iep2 fdbb0000.iep: allocate roi buffer failed
[    1.695476] mpp-iep2 fdbb0000.iep: probing finish
[    1.695667] mpp_jpgdec fdb90000.jpegd: Adding to iommu group 4
[    1.695838] mpp_jpgdec fdb90000.jpegd: probe device
[    1.696041] mpp_jpgdec fdb90000.jpegd: probing finish
[    1.696385] mpp_rkvdec2 fdc30000.rkvdec-ccu: rkvdec-ccu, probing start
[    1.696450] mpp_rkvdec2 fdc30000.rkvdec-ccu: probing finish
[    1.696548] mpp_rkvdec2 fdc38100.rkvdec-core: Adding to iommu group 12
[    1.696800] mpp_rkvdec2 fdc38100.rkvdec-core: rkvdec-core, probing start
[    1.696935] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_a is not found!
[    1.696940] rkvdec2_init:697: No niu aclk reset resource define
[    1.696945] mpp_rkvdec2 fdc38100.rkvdec-core: shared_niu_h is not found!
[    1.696949] rkvdec2_init:700: No niu hclk reset resource define
[    1.697001] mpp_rkvdec2 fdc38100.rkvdec-core: core_mask=00010001
[    1.697006] mpp_rkvdec2 fdc38100.rkvdec-core: attach ccu as core 0
[    1.697091] mpp_rkvdec2 fdc38100.rkvdec-core: sram_start 0x00000000fd600000
[    1.697096] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_iova 0x0000000010000000
[    1.697101] mpp_rkvdec2 fdc38100.rkvdec-core: sram_size 524288
[    1.697105] mpp_rkvdec2 fdc38100.rkvdec-core: rcb_size 1048576
[    1.697110] mpp_rkvdec2 fdc38100.rkvdec-core: min_width 512
[    1.697141] mpp_rkvdec2 fdc38100.rkvdec-core: probing finish
[    1.697228] mpp_rkvdec2 fdc48100.rkvdec-core: Adding to iommu group 13
[    1.697449] mpp_rkvdec2 fdc48100.rkvdec-core: rkvdec-core, probing start
[    1.697580] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_a is not found!
[    1.697585] rkvdec2_init:697: No niu aclk reset resource define
[    1.697590] mpp_rkvdec2 fdc48100.rkvdec-core: shared_niu_h is not found!
[    1.697594] rkvdec2_init:700: No niu hclk reset resource define
[    1.697632] mpp_rkvdec2 fdc48100.rkvdec-core: core_mask=00020002
[    1.697658] mpp_rkvdec2 fdc48100.rkvdec-core: attach ccu as core 1
[    1.697742] mpp_rkvdec2 fdc48100.rkvdec-core: sram_start 0x00000000fd680000
[    1.697747] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_iova 0x0000000010100000
[    1.697751] mpp_rkvdec2 fdc48100.rkvdec-core: sram_size 524288
[    1.697755] mpp_rkvdec2 fdc48100.rkvdec-core: rcb_size 1048576
[    1.697760] mpp_rkvdec2 fdc48100.rkvdec-core: min_width 512
[    1.697793] mpp_rkvdec2 fdc48100.rkvdec-core: probing finish
[    1.697985] mpp_rkvenc2 rkvenc-ccu: probing start
[    1.697992] mpp_rkvenc2 rkvenc-ccu: probing finish
[    1.698104] mpp_rkvenc2 fdbd0000.rkvenc-core: Adding to iommu group 10
[    1.698293] mpp_rkvenc2 fdbd0000.rkvenc-core: probing start
[    1.698312] mpp_rkvenc2 fdbd0000.rkvenc-core: link mode task capacity 8
[    1.698485] mpp_rkvenc2 fdbd0000.rkvenc-core: attach ccu as core 0
[    1.698578] mpp_rkvenc2 fdbd0000.rkvenc-core: probing finish
[    1.698646] mpp_rkvenc2 fdbe0000.rkvenc-core: Adding to iommu group 11
[    1.698835] mpp_rkvenc2 fdbe0000.rkvenc-core: probing start
[    1.698853] mpp_rkvenc2 fdbe0000.rkvenc-core: link mode task capacity 8
[    1.699029] mpp_rkvenc2 fdbe0000.rkvenc-core: attach ccu as core 1
[    1.699124] mpp_rkvenc2 fdbe0000.rkvenc-core: probing finish
[    1.699643] mpp_av1dec: Adding child /av1d@fdc70000
[    1.699892] mpp_av1dec: register device av1d-master
[    1.699915] mpp_av1dec av1d-master: av1_iommu_of_xlate,784
[    1.699937] av1_iommu_probe_device,736, consumer : av1d-master, supplier : fdca0000.iommu
[    1.699946] mpp_av1dec av1d-master: Adding to iommu group 15
[    1.700157] mpp_av1dec av1d-master: probing start
[    1.700385] mpp_av1dec av1d-master: probing finish
[    1.700427] mpp_service mpp-srv: probe success
[    1.709191] dma-pl330 fea10000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.709203] dma-pl330 fea10000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    1.710319] dma-pl330 fea30000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.710329] dma-pl330 fea30000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    1.711446] dma-pl330 fed10000.dma-controller: Loaded driver for PL330 DMAC-241330
[    1.711456] dma-pl330 fed10000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    1.712871] rockchip-pvtm fda40000.pvtm: pvtm@0 probed
[    1.712955] rockchip-pvtm fda50000.pvtm: pvtm@1 probed
[    1.713021] rockchip-pvtm fda60000.pvtm: pvtm@2 probed
[    1.713084] rockchip-pvtm fdaf0000.pvtm: pvtm@3 probed
[    1.713145] rockchip-pvtm fdb30000.pvtm: pvtm@4 probed
[    1.713843] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    1.714743] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    1.716248] random: fast init done
[    1.716346] random: crng init done
[    1.717078] rockchip-vop2 fdd90000.vop: Adding to iommu group 14
[    1.724942] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x5, primary plane phy id: 2
[    1.724958] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp1 assign plane mask: 0xa, primary plane phy id: 3
[    1.724977] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x140, primary plane phy id: 8
[    1.724988] rockchip-vop2 fdd90000.vop: [drm:vop2_bind] vp3 assign plane mask: 0x280, primary plane phy id: 9
[    1.725243] [drm] unsupported AFBC format[3231564e]
[    1.725290] [drm] failed to init overlay plane Cluster0-win1
[    1.725337] [drm] failed to init overlay plane Cluster1-win1
[    1.725390] [drm] failed to init overlay plane Cluster2-win1
[    1.725434] [drm] failed to init overlay plane Cluster3-win1
[    1.739549] rockchip-drm display-subsystem: bound fdd90000.vop (ops 0xffffffc010f83fe0)
[    1.740269] dwhdmi-rockchip fde80000.hdmi: registered ddc I2C bus driver
[    1.740495] rockchip-drm display-subsystem: bound fde80000.hdmi (ops 0xffffffc010f8bcb8)
[    1.741138] dwhdmi-rockchip fdea0000.hdmi: registered ddc I2C bus driver
[    1.741304] debugfs: Directory 'dw-hdmi' with parent '/' already present!
[    1.741313] dwhdmi-rockchip fdea0000.hdmi: failed to create debugfs dir!
[    1.741350] rockchip-drm display-subsystem: bound fdea0000.hdmi (ops 0xffffffc010f8bcb8)
[    1.741835] rockchip-drm display-subsystem: connector[HDMI-A-1] can't found any modes
[    1.741924] rockchip-drm display-subsystem: connector[HDMI-A-2] can't found any modes
[    1.741933] rockchip-drm display-subsystem: can't not find any logo display
[    1.741942] rockchip-drm display-subsystem: failed to show kernel logo
[    1.741972] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes
[    1.742522] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[    1.750545] brd: module loaded
[    1.754195] loop: module loaded
[    1.754444] zram: Added device: zram0
[    1.754620] lkdtm: No crash points registered, enable through debugfs
[    1.754763] system_heap: orders[0] = 6
[    1.754769] system_heap: orders[1] = 4
[    1.754774] system_heap: orders[2] = 0
[    1.756036] ahci fe210000.sata: supply ahci not found, using dummy regulator
[    1.756137] ahci fe210000.sata: supply phy not found, using dummy regulator
[    1.756267] ahci fe210000.sata: supply target not found, using dummy regulator
[    1.756342] ahci fe210000.sata: forcing port_map 0x0 -> 0x1
[    1.756368] ahci fe210000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[    1.756378] ahci fe210000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst 
[    1.756389] ahci fe210000.sata: port 0 can do FBS, forcing FBSCP
[    1.757139] scsi host0: ahci
[    1.757315] ata1: SATA max UDMA/133 mmio [mem 0xfe210000-0xfe210fff] port 0x100 irq 66
[    1.757420] ahci fe230000.sata: supply ahci not found, using dummy regulator
[    1.757502] ahci fe230000.sata: supply phy not found, using dummy regulator
[    1.757624] ahci fe230000.sata: supply target not found, using dummy regulator
[    1.757690] ahci fe230000.sata: forcing port_map 0x0 -> 0x1
[    1.757713] ahci fe230000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[    1.757722] ahci fe230000.sata: flags: ncq sntf pm led clo only pmp fbs pio slum part ccc apst 
[    1.757730] ahci fe230000.sata: port 0 can do FBS, forcing FBSCP
[    1.758219] scsi host1: ahci
[    1.758353] ata2: SATA max UDMA/133 mmio [mem 0xfe230000-0xfe230fff] port 0x100 irq 67
[    1.759584] rockchip-spi feb20000.spi: no high_speed pinctrl state
[    1.761138] rk806 spi2.0: chip id: RK806,ver:0x2, 0x1
[    1.761300] rk806 spi2.0: ON: 0x40 OFF:0x0
[    1.763456] vdd_gpu_s0: supplied by vcc5v0_sys
[    1.764176] vdd_cpu_lit_s0: supplied by vcc5v0_sys
[    1.764964] vdd_log_s0: supplied by vcc5v0_sys
[    1.765706] vdd_vdenc_s0: supplied by vcc5v0_sys
[    1.766487] vdd_ddr_s0: supplied by vcc5v0_sys
[    1.766990] vdd2_ddr_s3: supplied by vcc5v0_sys
[    1.767752] vdd_2v0_pldo_s3: supplied by vcc5v0_sys
[    1.768486] vcc_3v3_s3: supplied by vcc5v0_sys
[    1.769143] vddq_ddr_s0: supplied by vcc5v0_sys
[    1.769940] vcc_1v8_s3: supplied by vcc5v0_sys
[    1.770624] vdd_0v75_s3: supplied by vcc_1v1_nldo_s3
[    1.771355] vdd_ddr_pll_s0: supplied by vcc_1v1_nldo_s3
[    1.772031] avdd_0v75_s0: supplied by vcc_1v1_nldo_s3
[    1.772696] vdd_0v85_s0: supplied by vcc_1v1_nldo_s3
[    1.773372] nldo5_s0: supplied by vcc_1v1_nldo_s3
[    1.774097] avcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[    1.774905] vcc_1v8_s0: supplied by vdd_2v0_pldo_s3
[    1.775631] avdd_1v2_s0: supplied by vdd_2v0_pldo_s3
[    1.776350] vcc_3v3_s0: supplied by vcc5v0_sys
[    1.776988] vccio_sd_s0: supplied by vcc5v0_sys
[    1.777643] pldo6_s3: supplied by vcc5v0_sys
[    1.778252] rk806 spi2.0: no sleep-setting state
[    1.778261] rk806 spi2.0: no reset-setting pinctrl state
[    1.778267] rk806 spi2.0: no dvs-setting pinctrl state
[    1.780661] libphy: Fixed MDIO Bus: probed
[    1.781507] rk_gmac-dwmac fe1c0000.ethernet: IRQ eth_lpi not found
[    1.781691] rk_gmac-dwmac fe1c0000.ethernet: no regulator found
[    1.781701] rk_gmac-dwmac fe1c0000.ethernet: clock input or output? (output).
[    1.781708] rk_gmac-dwmac fe1c0000.ethernet: TX delay(0x43).
[    1.781715] rk_gmac-dwmac fe1c0000.ethernet: Can not read property: rx_delay.
[    1.781721] rk_gmac-dwmac fe1c0000.ethernet: set rx_delay to 0xffffffff
[    1.781733] rk_gmac-dwmac fe1c0000.ethernet: integrated PHY? (no).
[    1.781742] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_rx
[    1.781750] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock mac_clk_tx
[    1.781768] rk_gmac-dwmac fe1c0000.ethernet: cannot get clock clk_mac_speed
[    1.781987] rk_gmac-dwmac fe1c0000.ethernet: init for RGMII_RXID
[    1.782081] rk_gmac-dwmac fe1c0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[    1.782089] rk_gmac-dwmac fe1c0000.ethernet:         DWMAC4/5
[    1.782096] rk_gmac-dwmac fe1c0000.ethernet: DMA HW capability register supported
[    1.782103] rk_gmac-dwmac fe1c0000.ethernet: RX Checksum Offload Engine supported
[    1.782109] rk_gmac-dwmac fe1c0000.ethernet: TX Checksum insertion supported
[    1.782114] rk_gmac-dwmac fe1c0000.ethernet: Wake-Up On Lan supported
[    1.782153] rk_gmac-dwmac fe1c0000.ethernet: TSO supported
[    1.782160] rk_gmac-dwmac fe1c0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.782167] rk_gmac-dwmac fe1c0000.ethernet: Enabled Flow TC (entries=2)
[    1.782173] rk_gmac-dwmac fe1c0000.ethernet: TSO feature enabled
[    1.782180] rk_gmac-dwmac fe1c0000.ethernet: Using 32 bits DMA width
[    1.896168] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[    1.915013] libphy: stmmac: probed
[    1.917058] rk_gmac-dwmac fe1b0000.ethernet: IRQ eth_lpi not found
[    1.917305] rk_gmac-dwmac fe1b0000.ethernet: no regulator found
[    1.917313] rk_gmac-dwmac fe1b0000.ethernet: clock input or output? (output).
[    1.917320] rk_gmac-dwmac fe1b0000.ethernet: TX delay(0x43).
[    1.917327] rk_gmac-dwmac fe1b0000.ethernet: Can not read property: rx_delay.
[    1.917333] rk_gmac-dwmac fe1b0000.ethernet: set rx_delay to 0xffffffff
[    1.917344] rk_gmac-dwmac fe1b0000.ethernet: integrated PHY? (no).
[    1.917353] rk_gmac-dwmac fe1b0000.ethernet: cannot get clock mac_clk_rx
[    1.917360] rk_gmac-dwmac fe1b0000.ethernet: cannot get clock mac_clk_tx
[    1.917377] rk_gmac-dwmac fe1b0000.ethernet: cannot get clock clk_mac_speed
[    1.917601] rk_gmac-dwmac fe1b0000.ethernet: init for RGMII_RXID
[    1.917697] rk_gmac-dwmac fe1b0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[    1.917706] rk_gmac-dwmac fe1b0000.ethernet:         DWMAC4/5
[    1.917713] rk_gmac-dwmac fe1b0000.ethernet: DMA HW capability register supported
[    1.917720] rk_gmac-dwmac fe1b0000.ethernet: RX Checksum Offload Engine supported
[    1.917725] rk_gmac-dwmac fe1b0000.ethernet: TX Checksum insertion supported
[    1.917731] rk_gmac-dwmac fe1b0000.ethernet: Wake-Up On Lan supported
[    1.917769] rk_gmac-dwmac fe1b0000.ethernet: TSO supported
[    1.917776] rk_gmac-dwmac fe1b0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.917783] rk_gmac-dwmac fe1b0000.ethernet: Enabled Flow TC (entries=2)
[    1.917789] rk_gmac-dwmac fe1b0000.ethernet: TSO feature enabled
[    1.917795] rk_gmac-dwmac fe1b0000.ethernet: Using 32 bits DMA width
[    1.921701] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[    1.948373] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[    1.975043] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[    2.001706] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[    2.028372] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[    2.048348] libphy: stmmac: probed
[    2.050232] usbcore: registered new interface driver rtl8150
[    2.050265] usbcore: registered new interface driver r8152
[    2.058361] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[    2.063717] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.063735] ehci-pci: EHCI PCI platform driver
[    2.063768] ehci-platform: EHCI generic platform driver
[    2.066221] ehci-platform fc800000.usb: EHCI Host Controller
[    2.066318] ehci-platform fc800000.usb: new USB bus registered, assigned bus number 1
[    2.066394] ehci-platform fc800000.usb: irq 19, io mem 0xfc800000
[    2.071592] ata2: SATA link down (SStatus 0 SControl 300)
[    2.071655] ata1: SATA link down (SStatus 0 SControl 300)
[    2.078359] ehci-platform fc800000.usb: USB 2.0 started, EHCI 1.00
[    2.078470] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.078478] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.078485] usb usb1: Product: EHCI Host Controller
[    2.078491] usb usb1: Manufacturer: Linux 5.10.66 ehci_hcd
[    2.078497] usb usb1: SerialNumber: fc800000.usb
[    2.078759] hub 1-0:1.0: USB hub found
[    2.078780] hub 1-0:1.0: 1 port detected
[    2.081394] ehci-platform fc880000.usb: EHCI Host Controller
[    2.081495] ehci-platform fc880000.usb: new USB bus registered, assigned bus number 2
[    2.081560] ehci-platform fc880000.usb: irq 21, io mem 0xfc880000
[    2.085046] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[    2.091691] ehci-platform fc880000.usb: USB 2.0 started, EHCI 1.00
[    2.091795] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.091803] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.091810] usb usb2: Product: EHCI Host Controller
[    2.091815] usb usb2: Manufacturer: Linux 5.10.66 ehci_hcd
[    2.091822] usb usb2: SerialNumber: fc880000.usb
[    2.092057] hub 2-0:1.0: USB hub found
[    2.092077] hub 2-0:1.0: 1 port detected
[    2.092495] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.092509] ohci-platform: OHCI generic platform driver
[    2.092687] ohci-platform fc840000.usb: Generic Platform OHCI controller
[    2.092778] ohci-platform fc840000.usb: new USB bus registered, assigned bus number 3
[    2.092835] ohci-platform fc840000.usb: irq 20, io mem 0xfc840000
[    2.111710] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[    2.138375] rk-pcie fe170000.pcie: PCIe Linking... LTSSM is 0x3
[    2.152446] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    2.152457] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.152464] usb usb3: Product: Generic Platform OHCI controller
[    2.152470] usb usb3: Manufacturer: Linux 5.10.66 ohci_hcd
[    2.152476] usb usb3: SerialNumber: fc840000.usb
[    2.152710] hub 3-0:1.0: USB hub found
[    2.152731] hub 3-0:1.0: 1 port detected
[    2.153056] ohci-platform fc8c0000.usb: Generic Platform OHCI controller
[    2.153151] ohci-platform fc8c0000.usb: new USB bus registered, assigned bus number 4
[    2.153212] ohci-platform fc8c0000.usb: irq 22, io mem 0xfc8c0000
[    2.212453] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    2.212465] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.212472] usb usb4: Product: Generic Platform OHCI controller
[    2.212478] usb usb4: Manufacturer: Linux 5.10.66 ohci_hcd
[    2.212484] usb usb4: SerialNumber: fc8c0000.usb
[    2.212728] hub 4-0:1.0: USB hub found
[    2.212748] hub 4-0:1.0: 1 port detected
[    2.213425] phy phy-fd5d4000.syscon:usb2-phy@4000.3: illegal mode
[    2.213437] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    2.213537] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[    2.213635] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[    2.213665] xhci-hcd xhci-hcd.9.auto: irq 121, io mem 0xfc400000
[    2.213826] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    2.213834] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.213840] usb usb5: Product: xHCI Host Controller
[    2.213846] usb usb5: Manufacturer: Linux 5.10.66 xhci-hcd
[    2.213852] usb usb5: SerialNumber: xhci-hcd.9.auto
[    2.214084] hub 5-0:1.0: USB hub found
[    2.214105] hub 5-0:1.0: 1 port detected
[    2.214280] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    2.214365] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 6
[    2.214377] xhci-hcd xhci-hcd.9.auto: Host supports USB 3.0 SuperSpeed
[    2.214414] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    2.214475] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[    2.214482] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.214488] usb usb6: Product: xHCI Host Controller
[    2.214494] usb usb6: Manufacturer: Linux 5.10.66 xhci-hcd
[    2.214500] usb usb6: SerialNumber: xhci-hcd.9.auto
[    2.214729] hub 6-0:1.0: USB hub found
[    2.214748] hub 6-0:1.0: 1 port detected
[    2.214988] usbcore: registered new interface driver cdc_acm
[    2.214995] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    2.215124] usbcore: registered new interface driver uas
[    2.215193] usbcore: registered new interface driver usb-storage
[    2.215239] usbcore: registered new interface driver usbserial_generic
[    2.215255] usbserial: USB Serial support registered for generic
[    2.215280] usbcore: registered new interface driver cp210x
[    2.215293] usbserial: USB Serial support registered for cp210x
[    2.215336] usbcore: registered new interface driver ftdi_sio
[    2.215349] usbserial: USB Serial support registered for FTDI USB Serial Device
[    2.215457] usbcore: registered new interface driver keyspan
[    2.215470] usbserial: USB Serial support registered for Keyspan - (without firmware)
[    2.215484] usbserial: USB Serial support registered for Keyspan 1 port adapter
[    2.215498] usbserial: USB Serial support registered for Keyspan 2 port adapter
[    2.215511] usbserial: USB Serial support registered for Keyspan 4 port adapter
[    2.215538] usbcore: registered new interface driver option
[    2.215552] usbserial: USB Serial support registered for GSM modem (1-port)
[    2.215705] usbcore: registered new interface driver oti6858
[    2.215718] usbserial: USB Serial support registered for oti6858
[    2.215741] usbcore: registered new interface driver pl2303
[    2.215754] usbserial: USB Serial support registered for pl2303
[    2.215785] usbcore: registered new interface driver qcserial
[    2.215798] usbserial: USB Serial support registered for Qualcomm USB modem
[    2.215836] usbcore: registered new interface driver sierra
[    2.215850] usbserial: USB Serial support registered for Sierra USB modem
[    2.216412] usbcore: registered new interface driver usbtouchscreen
[    2.217537] input: rk805 pwrkey as /devices/platform/feb20000.spi/spi_master/spi2/spi2.0/rk805-pwrkey.7.auto/input/input0
[    2.217840] i2c /dev entries driver
[    2.220997] vdd_cpu_big0_s0: supplied by vcc5v0_sys
[    2.229047] vdd_cpu_big1_s0: supplied by vcc5v0_sys
[    2.237730] vdd_npu_s0: supplied by vcc5v0_sys
[    2.266683] rtc-hym8563 6-0051: rtc information is valid
[    2.272128] rtc-hym8563 6-0051: registered as rtc0
[    2.273170] rtc-hym8563 6-0051: setting system clock to 2000-01-01T00:32:47 UTC (946686767)
[    2.282582] usbcore: registered new interface driver uvcvideo
[    2.282611] USB Video Class driver (1.1.1)
[    2.285397] rockchip-thermal fec00000.tsadc: Missing rockchip,grf property
[    2.286542] rockchip-thermal fec00000.tsadc: tsadc is probed successfully!
[    2.287389] Bluetooth: HCI UART driver ver 2.3
[    2.287413] Bluetooth: HCI UART protocol H4 registered
[    2.287424] Bluetooth: HCI UART protocol ATH3K registered
[    2.287500] usbcore: registered new interface driver bfusb
[    2.287570] usbcore: registered new interface driver btusb
[    2.288167] cpu cpu0: leakage=10
[    2.289903] cpu cpu0: pvtm=1435
[    2.290125] cpu cpu0: pvtm-volt-sel=2
[    2.291048] cpu cpu4: leakage=8
[    2.297971] cpu cpu4: pvtm=1670
[    2.302139] cpu cpu4: pvtm-volt-sel=1
[    2.303711] cpu cpu6: leakage=8
[    2.310548] cpu cpu6: pvtm=1673
[    2.314709] cpu cpu6: pvtm-volt-sel=1
[    2.317510] cpu cpu0: avs=0
[    2.319420] cpu cpu4: avs=0
[    2.321270] cpu cpu6: avs=0
[    2.321905] cpu cpu0: EM: created perf domain
[    2.322034] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    2.323584] cpu cpu4: EM: created perf domain
[    2.323714] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    2.326613] cpu cpu6: EM: created perf domain
[    2.326685] cpu cpu6: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    2.330402] sdhci: Secure Digital Host Controller Interface driver
[    2.330422] sdhci: Copyright(c) Pierre Ossman
[    2.330430] Synopsys Designware Multimedia Card Interface Driver
[    2.331290] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.331697] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    2.331872] dwmmc_rockchip fe2c0000.mmc: IDMAC supports 32-bit address mode.
[    2.331917] dwmmc_rockchip fe2c0000.mmc: Using internal DMA controller.
[    2.331930] dwmmc_rockchip fe2c0000.mmc: Version ID is 270a
[    2.331971] dwmmc_rockchip fe2c0000.mmc: DW MMC controller at irq 68,32 bit host data width,256 deep fifo
[    2.332840] leds-gpio: probe of leds failed with error -16
[    2.332955] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
[    2.333006] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[    2.333883] cryptodev: driver 1.12 loaded.
[    2.333926] hid: raw HID events driver (C) Jiri Kosina
[    2.334129] usbcore: registered new interface driver usbhid
[    2.334138] usbhid: USB HID core driver
[    2.345669] optee: probing for conduit method.
[    2.345697] optee: revision 3.13 (8e053a88)
[    2.346120] optee: initialized driver
[    2.346727] usbcore: registered new interface driver snd-usb-audio
[    2.355224] input: rockchip-hdmi0 rockchip-hdmi0 as /devices/platform/hdmi0-sound/sound/card0/input1
[    2.356874] input: rockchip-hdmi1 rockchip-hdmi1 as /devices/platform/hdmi1-sound/sound/card1/input2
[    2.356958] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    2.357910] input: headset-keys as /devices/platform/es8388-sound/input/input3
[    2.368445] mmc1: SDHCI controller on fe2e0000.mmc [fe2e0000.mmc] using ADMA
[    2.371698] ES8323 7-0011: ASoC: error at soc_component_write_no_lock on ES8323.7-0011: -5
[    2.404834] mmc1: new HS400 Enhanced strobe MMC card at address 0001
[    2.405539] mmcblk1: mmc1:0001 BJTD4R 29.1 GiB 
[    2.405710] mmcblk1boot0: mmc1:0001 BJTD4R partition 1 4.00 MiB
[    2.405885] mmcblk1boot1: mmc1:0001 BJTD4R partition 2 4.00 MiB
[    2.406251] mmcblk1rpmb: mmc1:0001 BJTD4R partition 3 4.00 MiB, chardev (236:0)
[    2.409369]  mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8
[    2.422992] input: rockchip-es8388 Headset as /devices/platform/es8388-sound/sound/card2/input4
[    2.424215] Initializing XFRM netlink socket
[    2.424643] NET: Registered protocol family 10
[    2.425708] Segment Routing with IPv6
[    2.425775] NET: Registered protocol family 17
[    2.425795] NET: Registered protocol family 15
[    2.425931] Bluetooth: RFCOMM socket layer initialized
[    2.425953] Bluetooth: RFCOMM ver 1.11
[    2.425967] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.425979] Bluetooth: HIDP socket layer initialized
[    2.426015] [BT_RFKILL]: Enter rfkill_rk_init
[    2.426023] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    2.426624] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    2.426662] [WLAN_RFKILL]: can't find rockchip,grf property
[    2.426672] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6275P
[    2.426680] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    2.426688] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    2.426713] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,poweren_gpio = 20 flags = 0.
[    2.426744] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[    2.426752] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    2.426761] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
[    2.426770] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[    2.427135] Key type dns_resolver registered
[    2.428542] Loading compiled-in X.509 certificates
[    2.429403] pstore: Using crash dump compression: deflate
[    2.429753] rga3_core0 fdb60000.rga: Adding to iommu group 2
[    2.430010] rga: rga3_core0_irq, irq = 32, match scheduler
[    2.430361] rga: rga3_core0 driver loaded successfully ver:3.0.76831
[    2.430391] rga: rga3_core0 probe successfully
[    2.430869] rga3_core1 fdb70000.rga: Adding to iommu group 3
[    2.431039] rga: rga3_core1_irq, irq = 33, match scheduler
[    2.431221] rga: rga3_core1 driver loaded successfully ver:3.0.76831
[    2.431241] rga: rga3_core1 probe successfully
[    2.431605] rga: rga2_irq, irq = 34, match scheduler
[    2.431831] rga: rga2 driver loaded successfully ver:3.2.63318
[    2.431843] rga: rga2 probe successfully
[    2.432248] rga: Module initialized. v1.2.7
[    2.452364] vendor storage:20190527 ret = 0
[    2.461708] usb 5-1: new high-speed USB device number 2 using xhci-hcd
[    2.467511] pcie20_avdd0v85: supplied by vdd_0v85_s0
[    2.467924] mali fb000000.gpu: Kernel DDK version g11p0-01eac0
[    2.468181] pcie20_avdd1v8: supplied by avcc_1v8_s0
[    2.468573] pcie30_avdd0v75: supplied by avdd_0v75_s0
[    2.469458] pcie30_avdd1v8: supplied by avcc_1v8_s0
[    2.470038] vcc3v3_lcd0_n: supplied by vcc_1v8_s3
[    2.470457] mali fb000000.gpu: leakage=13
[    2.470565] vcc3v3_pcie30: supplied by vcc_3v3_s0
[    2.471436] input: adc-keys as /devices/platform/adc-keys/input/input5
[    2.472550] mali fb000000.gpu: pvtm=875
[    2.472920] mali fb000000.gpu: pvtm-volt-sel=2
[    2.474447] mali fb000000.gpu: avs=0
[    2.475811] RKNPU fdab0000.npu: Adding to iommu group 0
[    2.475850] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 132; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[    2.475987] RKNPU fdab0000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
[    2.476426] mali fb000000.gpu: r0p0 status 5 is unknown; treating as r0p0 status 0
[    2.476448] mali fb000000.gpu: GPU identified as 0x7 arch 10.8.6 r0p0 status 0
[    2.476593] mali fb000000.gpu: No priority control manager is configured
[    2.476612] mali fb000000.gpu: No memory group manager is configured
[    2.476659] mali fb000000.gpu: Protected memory allocator not available
[    2.477308] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdab0000-0xfdabffff]
[    2.477334] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdac0000-0xfdacffff]
[    2.477348] RKNPU fdab0000.npu: can't request region for resource [mem 0xfdad0000-0xfdadffff]
[    2.477883] [drm] Initialized rknpu 0.6.4 20211227 for fdab0000.npu on minor 1
[    2.477946] mali fb000000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    2.479505] mali fb000000.gpu: Probed as mali0
[    2.480204] usb 1-1: New USB device found, idVendor=1a86, idProduct=55d5, bcdDevice=80.46
[    2.480231] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.480247] usb 1-1: Product: USB Quad_Serial
[    2.480260] usb 1-1: Manufacturer: wch.cn
[    2.480273] usb 1-1: SerialNumber: 0123456789
[    2.481207] RKNPU fdab0000.npu: leakage=7
[    2.488325] cdc_acm 1-1:1.0: ttyACM0: USB ACM device
[    2.489147] RKNPU fdab0000.npu: pvtm=848
[    2.493486] RKNPU fdab0000.npu: pvtm-volt-sel=1
[    2.493799] cdc_acm 1-1:1.2: ttyACM1: USB ACM device
[    2.494570] RKNPU fdab0000.npu: avs=0
[    2.494786] RKNPU fdab0000.npu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    2.497982] cdc_acm 1-1:1.4: ttyACM2: USB ACM device
[    2.502389] cdc_acm 1-1:1.6: ttyACM3: USB ACM device
[    2.502611] RKNPU fdab0000.npu: failed to find power_model node
[    2.502624] RKNPU fdab0000.npu: RKNPU: failed to initialize power model
[    2.502633] RKNPU fdab0000.npu: RKNPU: failed to get dynamic-coefficient
[    2.503242] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    2.505436] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    2.506439] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    2.506473] cfg80211: failed to load regulatory.db
[    2.507598] rockchip-pm rockchip-suspend: not set pwm-regulator-config
[    2.508883] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 405; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '09:01:29', on 'Aug 10 2022'.
[    2.509441] Mali: 
[    2.509446] Mali device driver loaded
[    2.509466] ALSA device list:
[    2.509475]   #0: rockchip-hdmi0
[    2.509485]   #1: rockchip-hdmi1
[    2.509494]   #2: rockchip-es8388
[    2.509503]   #3: rockchip,hdmiin
[    2.525035] rk-pcie fe170000.pcie: PCIe Link up, LTSSM is 0x30011
[    2.525185] rk-pcie fe170000.pcie: PCI host bridge to bus 0002:20
[    2.525212] pci_bus 0002:20: root bus resource [bus 20-2f]
[    2.525223] pci_bus 0002:20: root bus resource [??? 0xf2000000-0xf20fffff flags 0x0]
[    2.525231] pci_bus 0002:20: root bus resource [io  0x0000-0xfffff] (bus address [0xf2100000-0xf21fffff])
[    2.525239] pci_bus 0002:20: root bus resource [mem 0xf2200000-0xf2ffffff]
[    2.525246] pci_bus 0002:20: root bus resource [mem 0x980000000-0x9bfffffff pref]
[    2.525277] pci 0002:20:00.0: [1d87:3588] type 01 class 0x060400
[    2.525300] pci 0002:20:00.0: reg 0x38: [mem 0x00000000-0x0000ffff pref]
[    2.525359] pci 0002:20:00.0: supports D1 D2
[    2.525365] pci 0002:20:00.0: PME# supported from D0 D1 D3hot
[    2.530881] pci 0002:20:00.0: Primary bus is hard wired to 0
[    2.530891] pci 0002:20:00.0: bridge configuration invalid ([bus 01-ff]), reconfiguring
[    2.531085] pci 0002:21:00.0: [14e4:449d] type 00 class 0x028000
[    2.531183] pci 0002:21:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[    2.531236] pci 0002:21:00.0: reg 0x18: [mem 0x00000000-0x003fffff 64bit]
[    2.531786] pci 0002:21:00.0: supports D1 D2
[    2.531794] pci 0002:21:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    2.534435] EXT4-fs (mmcblk1p6): recovery complete
[    2.534918] EXT4-fs (mmcblk1p6): mounted filesystem with ordered data mode. Opts: (null)
[    2.534964] VFS: Mounted root (ext4 filesystem) on device 179:6.
[    2.535277] devtmpfs: mounted
[    2.537885] Freeing unused kernel memory: 6208K
[    2.550384] pci_bus 0002:21: busn_res: [bus 21-2f] end is updated to 21
[    2.550428] pci 0002:20:00.0: BAR 8: assigned [mem 0xf2200000-0xf27fffff]
[    2.550440] pci 0002:20:00.0: BAR 6: assigned [mem 0xf2800000-0xf280ffff pref]
[    2.550453] pci 0002:21:00.0: BAR 2: assigned [mem 0xf2400000-0xf27fffff 64bit]
[    2.550500] pci 0002:21:00.0: BAR 0: assigned [mem 0xf2200000-0xf220ffff 64bit]
[    2.550544] pci 0002:20:00.0: PCI bridge to [bus 21]
[    2.550554] pci 0002:20:00.0:   bridge window [mem 0xf2200000-0xf27fffff]
[    2.552700] pcieport 0002:20:00.0: PME: Signaling with IRQ 134
[    2.571895] Run /sbin/init as init process
[    2.601309] EXT4-fs (mmcblk1p6): re-mounted. Opts: (null)
[    2.609057] usb 5-1: New USB device found, idVendor=0424, idProduct=2734, bcdDevice= 2.02
[    2.609085] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.609095] usb 5-1: Product: USB2734
[    2.609103] usb 5-1: Manufacturer: Microchip Tech
Starting syslogd: OK
Starting klogd: OK
Running sysctl: OK
[    2.662808] hub 5-1:1.0: USB hub found
[    2.662901] hub 5-1:1.0: 5 ports detected
/usr/bin/modetest
